Xufeng Powder

Xufeng Powder Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Xufeng Powder, Mining Company, Floor 3rd, Hengtaixing Building, Yingbin Avenue, Qingmeng Development Area, Zayton.

🌍 Talc & Calcium Carbonate Supplier
🔬 High Purity | Stable Quality | Custom Grades
🏭 For Plastics, Rubber, Paint, Ceramics & More
📦 Exported to 50+ Countries | 5000+ Clients
📞 Free Samples | Expert Support
📲 WhatsApp: +86 18350592277

04/10/2026

👟 Local color spots on the surface of your shoe material? The defect is never random — there are three things worth checking first 🔍🏭
On the surface of the shoe material, there are local color spots 🟤 It's one of those problems you can't just polish away — and it shows up on the part, not in the machine data.

Usually we need to focus on three reasons 🧠

1️⃣ Firstly — better dispersibility and heat resistance of raw materials 🌡️
2️⃣ Secondly — mold temperature 🔥
3️⃣ Thirdly — the low-molecular materials in the formula 🧫

Then the practical fixes 🔧
▪️ Replace the colorant with better temperature resistance 🎨
▪️ Move to better raw materials and functional fillers 🧪
▪️ Make sure the pigment is uniformly dispersed 🌀
▪️ Improve the fluidity of the rubber 🌊
▪️ And finally — stabilize process control: formula, color material, mold temperature, vulcanization process 🎛️

Which of the three have you already ruled out — 1, 2 or 3? 👇 Often encounter the problem of color spots? You're welcome to discuss in the comment section 💬

📌 Technical data & selection support:
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277
(You can also contact us to obtain a solution. ☝️💬)

04/10/2026

⏰ GB 6246-2026 lands on 31 March 2027. If your liner compound still runs unmodified talc powder, the new standard may not pass 🚨
🚒
The new national standard for synthetic rubber fire hose is here 📜 — and filler selection is the cheapest thing to fix before it kicks in 💰

Three rules for talc powder in fire hose 🚒

1️⃣ Fineness 📏 For an EPDM liner you want 2,500 mesh — finer grades give you the surface and the dispersion the new test items are looking for 🔍

2️⃣ Addition amount ⚖️ Control it to 15–30 parts. Not more than 50 parts — after that, adhesion is the first thing to go 📉

3️⃣ The third, and the most important: coupling-agent treatment 🔬 This is the one most factories skip. Unmodified, hydrophobic talc doesn't bond with rubber 🚫💧 so the compound fails where it matters ❌

Drop 1 if you're already running surface-treated talc, 2 if you're still on unmodified powder 👇 Tell me which line you run and I'll send you the selection suggestions 📄

📌 Full tech data & quotation:
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277
(You can also contact us to obtain a solution. ☝️💬)

03/10/2026

If your liner compound still runs unmodified talc powder, the new standard may not pass 🚨

The new national standard for synthetic rubber fire hose is here 📜 — and filler selection is the cheapest thing to fix before it kicks in 💰

Three rules for talc powder in fire hose 🚒

1️⃣ Fineness 📏 For an EPDM liner you want 2,500 mesh — finer grades give you the surface and the dispersion the new test items are looking for 🔍

2️⃣ Addition amount ⚖️ Control it to 15–30 parts. Not more than 50 parts — after that, adhesion is the first thing to go 📉

3️⃣ The third, and the most important: coupling-agent treatment 🔬 This is the one most factories skip. Unmodified, hydrophobic talc doesn't bond with rubber 🚫💧 so the compound fails where it matters ❌

Drop 1 if you're already running surface-treated talc, 2 if you're still on unmodified powder 👇 Tell me which line you run and I'll send you the selection suggestions 📄

📌 Full tech data & quotation:
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277
(You can also contact us to obtain a solution. ☝️💬)

02/10/2026

💎 The filler looks like a minor line item in your formula. It's actually what decides whether your filament is clean ✨ or full of bulges and white spots 😩💎
Producing PLA and still getting bulges and white spots? 🖨️ Printed parts with defects all over the surface? Then the yield rate just won't go up 📉

The filler seems inconspicuous 🫥 — but run it a different way and the effect is completely different. In most cases the talc powder simply isn't dispersed properly 🌀❌

Three things to check first 🔍
▪️ the amount of filler you add ⚖️
▪️ the type you choose 🧪
▪️ the way you feed it in 🥄

What changes the picture is a high-transparency talc powder 💎 with a modified surface. Dispersion improves visibly ✨ the compatibility with PLA and PETG resins is good 🤝 whiteness holds ⚪ and it's produced from a high-purity mineral source 🏔️

Result: the printout effect is very good ✅ and the change in your formula is small 💰

Drop 1 if you run PLA, 2 if you run PETG 👇 I'll send you the grade recommendation 📄

📌 Full tech data & quotation:
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277
(You can also contact us to obtain a solution. ☝️💬)

01/10/2026

👟 Black smoke during sole injection? Sometimes good, sometimes bad — and one bad batch can waste the whole lot of material 😯🏭
You know that feeling: this batch of materials may be wasted 💸 And the worst part is you really don't know if it will appear — sometimes good, sometimes bad, no pattern 🤷

On the filler side, there are two things worth trying 🧪

1️⃣ Consider high-silicon or functional fillers — they help improve the fluidity of the rubber 🌊

2️⃣ Meanwhile, choose powders with good dispersion 🌀 It enables a more uniform compound system, which is where the real difference shows up.

What you get out of it 👇
▪️ Less flow anomaly caused by local powder aggregation 📉
▪️ Fewer flow marks and black streaks on the finished part 🎯
▪️ More consistency between batches ⚖️

Have you ever encountered black smoke from the soles? 👇 Tell me your material and cycle time — I'll tell you what we'd check first 🛠️

📌 Technical data & selection support:
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277
(You can also contact us to obtain a solution. ☝️💬)

30/09/2026

Bulges and white spots on your PLA filament? It's not the extruder — the filler is doing more damage than you think
🖨️
If you're producing PLA and every batch comes out with bulges and white spots 😩 and the printed parts have defects all over the surface, the yield rate will never climb 📉

The reason is usually the same: the talc powder is not dispersed properly 🌀❌

And it's not only the powder itself. Three variables decide the result 🔍
▪️ the amount of filler added ⚖️
▪️ the type of filler 🧪
▪️ the way it's added — powder, or particles? 🥄

Then there's the part most people skip 👇 surface modification of the additive. After modification you can clearly see the effect of reducing agglomeration ✨ and the compatibility with PLA and PETG resins goes way up 🤝

The grade we run is made from a high-purity mineral source 🏔️ with high whiteness ⚪ The printout effect is very good ✅

Drop 1 if you run PLA, 2 if you run PETG 👇 I'll send you the grade recommendation 📄

📌 Full tech data & quotation:
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277
(You can also contact us to obtain a solution. ☝️💬)

29/09/2026

Fire hose failed another random inspection? 🚒 Inner rubber layer won't bond to the braided layer — and no, it's not a glue problem.


It's the talc. 👇
Untreated talc filler has no film-forming property. Loaded in, it sits there like fine sand — blocking the rubber from touching and anchoring the braided fibers. Your adhesive never gets to pe*****te the rubber surface, so the two layers never truly lock.

Two ways out:
1️⃣ Coupling agent — flips the talc surface from hydrophobic to hydrophilic. Adhesion comes back. ✅
2️⃣ Control the dosage — don't dump filler in just to cut cost. The more you add, the worse the surface adhesion gets. ❌

Or skip the trial and error: use talc that's already surface-treated. 👉 Xufeng's coupling-agent-modified talc powder for rubber hose — bonds properly, keeps your cost down.

Ever had a hose fail on bonding? 🧐 Drop 1 = yes, 2 = never.
🌐 Website: www.xufengtalc.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277

28/09/2026

Filament snapping mid-print? 🖨️💥 Before you touch the printer — blame the filament first. 90% of the time, that's where the problem is. 🤔
Check #1 — the formula 🧪
Cheap filaments push filler loading too high. Not enough resin left to stay tough. Fillers = hardness & rigidity… overdone = brittle. ❌
Check #2 — moisture 💧
Untreated filler absorbs water. At print temp, it turns to steam → snap. No machine setting fixes that. 🚫⚙️
Ruled those out? Fix it in 3 steps 👇
1️⃣ Dry the filament 🔥
2️⃣ Ease the tension 🧵
3️⃣ Reduce bending & pulling 🌀
⚠️ Or skip the detective work — use a 3D-printing-specific toughening masterbatch. Filler + resin, already balanced. Rigid AND tough. 💪
🎬 Xufeng Powder walks you through the whole fix in this video.
Quick question 👇
Filament ever snapped mid-print?
Snapped → drop a 1️⃣
Never → drop a 2️⃣
🌐 www.xufengminerals.com
📧 [email protected]
📱 WhatsApp: +86-18350592277

27/09/2026

Still burning money on titanium dioxide? Stop. 🎨💸
Same industrial coating… but why do others stay bright and sun-proof while yours blackens and chalks within two years?

The problem may be hiding in your filler:
✅ Want high gloss? Barium sulfate — fine dense packing, light hits it and it shines
✅ Want maximum weather resistance? Barium sulfate — chemically inert, insoluble in acid & alkali, no chalking outdoors
✅ Want lower cost? Barium sulfate — directly replaces 10%–25% of TiO₂, with whiteness and hiding power still holding up

👉 Swap the filler, and the problem may just solve itself. Xufeng Powder explains how.
Struggling with the same issues? Comment "barium sulfate" and we'll send you detailed selection advice. 💬
🌐 Website: www.xufengminerals.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277

26/09/2026

Adding calcium carbonate to a flame-retardant PP — will your UL-94 rating drop? 🔥
Short answer: not necessarily. But the loading and the system matter a lot.

What's really happening:
⚠️ CaCO₃ is non-flammable and dilutes the combustible plastic — that helps
⚠️ But at high temperature it decomposes and absorbs heat, releasing CO₂ and diluting oxygen
⚠️ The catch: it splits the plastic matrix, creating a wick effect that accelerates heat transfer — and it can fight against some PP flame retardants (data shows flame-retardant PP can fail UL-94 V-2 and self-extinguishing)

✅ The practical answer: control loading within 10%, pick surface-activated CaCO₃, and match it to your flame-retardant system. Paired with intumescent flame retardants, nano CaCO₃ can even boost flame retardancy.

👉 In this video, Xufeng Powder explains how to make CaCO₃ work with your FR system, not against it.
Not sure how to match it? Comment "flame retardant" and we'll send you the selection guide. 💬
🌐 Website: www.xufengminerals.com
📧 E-Mail: [email protected]
📱 WhatsApp: +86-18350592277

Address

Floor 3rd, Hengtaixing Building, Yingbin Avenue, Qingmeng Development Area
Zayton
36200

Website

, ,

Alerts

Be the first to know and let us send you an email when Xufeng Powder posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category