MEC Aero DBF Team

MEC Aero DBF Team MEC AERO DBF Team participate Design Build Fly competition organized by AIAA. We Are Team Belong to "MEC" Mechanical Engineering Club

MEC AERO DBF Team participate Design Build Fly competition organized by AIAA Foundation where we Applied Aerodynamics, Aircraft Design, Design Engineering. Our Student teams will design, fabricate, and demonstrate the flight capabilities of an unmanned, electric powered, radio controlled aircraft which can best meet the specified mission profile. The goal is a balanced design possessing good demo

nstrated flight handling qualities and practical and affordable manufacturing requirements while providing a high vehicle performance.

07/09/2017

ازيكم يا شباب 😀
كل عام وانتم بخير

الrules بتاعت المسابقه نزلت من كام يوم وللاسف احنا متاخرين فياريت الناس اللي هتشارك تبعت ال cv وهيتم التواصل معاهم بحيث نبدا الاسبوع الجاي الشغل علاطول ان شاء الله

الميل ([email protected])
Deadline ;tommorow 10 pm

كل سنه وانتم طيبين😄😄يسعدنا  ان نذكركم بمسابقة DBF وهي مسابقة تقام سنويا في الولايات المتحده وبيحكم فيها ناس من ناسا وبين...
19/08/2017

كل سنه وانتم طيبين😄😄
يسعدنا ان نذكركم بمسابقة DBF وهي مسابقة تقام سنويا في الولايات المتحده وبيحكم فيها ناس من ناسا وبينظمها المعهد الامريكي للطيران والفضاء AIAA

انتظروا ايفينت بعد العيد ان شاء الله -هننزل بتفاصيل المكان- وهنجيب ناس من فرقنا السابقه يكلموكم عن المسابقه والsessions والشغل بالتفاصيل ويسمعوا استفساراتكم ويردوا عليها ..وهنرفع فورم تسجيل علشان الناس اللي هتشارك معانا 💪💪💪

منظرينكم 😃😃

بعدما أرسلنا التقرير المطلوب عن تصميم الطائرة تم قبوله وإعلان فريق MEC AERO DBF TEAM جامعة طنطا ضمن المنافسين فى المسابق...
28/02/2015

بعدما أرسلنا التقرير المطلوب عن تصميم الطائرة تم قبوله وإعلان فريق MEC AERO DBF TEAM جامعة طنطا ضمن المنافسين فى المسابقة التى ستجُرى أول شهر إبريل القادم فى مدينة توسان التابعة لولاية أريزونا فى الولايات المتحدة الأمريكية ، وبلغ عدد المنافسين فى تلك المسابقة 84 فريق من جامعات العالم المختلفة ونحن نرجو من الله أن يوفقنا الأيام المقبله ونستطيع الإنتهاء من إجراءات السفر وأن ننافس بقوة ونحقق نجاحا يشرفنا ويشرف بلدنا وجامعتنا إن شاء الله :)
**********************************************************************************
We sent a report about the design of our plane successfully before the deadline, so now we can say it loudly that for the first time team from Tanta University will challenge other foreign team next April in AIAA D.B.F,competition which will be in Tucson Arizona USA.
We hope to go there and make an achievement. :)


#دعواتكم

Session about UAV.*What's UAV?!*Autopilot?
10/02/2015

Session about UAV.
*What's UAV?!
*Autopilot?

Session about Design.It was a good start to teach members how to think and share ideas with each other by giving them so...
07/02/2015

Session about Design.
It was a good start to teach members how to think and share ideas with each other by giving them some problems to solve. They've learnt some basics about aircraft design.

Session about Fundamentals of Fluid Mechanics.*Fluid?*Dimensions and Unit.*Properties Of Fluid.*Equation of state.*Type ...
25/01/2015

Session about Fundamentals of Fluid Mechanics.
*Fluid?
*Dimensions and Unit.
*Properties Of Fluid.
*Equation of state.
*Type Of Flow
*Fluid Motion Description.
*Circulation
*Rotation
*Vorticity
*Rotational & Irrotational Flow.
*Boundary Layer, Flow Separation.

وبعد أن تحدثنا عن المهمتين الأولى والثانيه جاء وقت الثالثه والأخيره وهى تعّد الأهم والأصعب من بين الثلاث مهمات حيث ينبغى...
23/01/2015

وبعد أن تحدثنا عن المهمتين الأولى والثانيه جاء وقت الثالثه والأخيره وهى تعّد الأهم والأصعب من بين الثلاث مهمات حيث ينبغى أن تحمل الطائرة حمولة متمثله فى كرات بلاستيكية وزن الكرة 68 جرام ومحيطها 12 بوصه (30.48) سم كما هو موضح بالصورة
نحن من نختار عدد الكرات التى ستحملها الطائرة ويجب أن تقوم الطائره بالقاء الكره فى المكان الموضح على الخريطه بمقدار كرة كل لفه
صعوبة المهمه تكمن فى كيفية وضع الكرات على متن الطائره حيث من شروط تلك المهمه أن لا توضع الكرات بداخل جسم الطائره بل خارجها فيتوجب علينا تحديد المكان المناسب لوضع الكرات دون أن يؤئر ذلك تأثيرا كبيرا على أداء الطائره كما يتعين علينا صنع ميكانيزم ما يقوم بالقاء الكرات بالطريقه التى ذكرت بالأعلى .
يتم حساب نتيجة هذه المهمه كالآتى :
M3= 6 * (N_Laps_Flown / Max_N_Laps_Flown)
ومن الواجب والمهم أن تقوم الطائره بهبوط ناجح كالمهمتين السابقتين
******************************************************
After we've talked about the 1st and 2nd mission, now it’s the time to talk about the 3rd and last one.
3rd mission is the most important and the most difficult of all as it would be like this:
Take-off within the prescribed field length.
All payloads and supporting equipment (including restraint and release mechanisms, fairings,
etc.) must be properly secured external to the airplane configuration flown in missions 1 and 2.
External is defined to be exposed to the air when viewed from at least three sides (top,
bottom, left, right)
Payload will be a team-selected number of Champro 12" Plastic Balls (12" Circumference
"Softball" size).
The payload during the competition will be provided by contest officials.
Nominal weight for each ball is approximately 2.4 ounces (68 grams)
On each lap, while airborne, the airplane will remotely drop a single ball
CG may not vary outside of design limits during the mission.
The drop shall occur in a “drop zone”
*On the upwind leg, flight in the direction of the takeoff
*Between the upwind/downwind turn stations
*On the runway side opposite the spectators
A lap will only count if a single ball is dropped within the drop zone.
Multiple drops in the zone on a single lap will invalidate that lap.
No other part of the airplane or payload mounting system may drop with the ball
Mission score:
M3= 6 * (N_Laps_Flown / Max_N_Laps_Flown)
Must complete a successful landing to get a score .

05/01/2015

History and Heritage _ The American Institute of Aeronautics and Astronautics

Happy New Year to all our fans... its the first Christmas ... :) :D
31/12/2014

Happy New Year to all our fans... its the first Christmas ... :) :D

mission one in simple Alabama D.B.F 14/3/2014
30/12/2014

mission one in simple
Alabama D.B.F 14/3/2014

The University of Alabama Design, Build, Fly Aircraft (Bama Bushwacker) mission one practice flight on March 14, 2014. This is a Senior Design project at the...

 Introduction to Aerodynamic:-Wing Geometry Definitions-Airfoil Geometry Definitions-Angle of attack - Lift Equation-Sta...
29/12/2014


Introduction to Aerodynamic:
-Wing Geometry Definitions
-Airfoil Geometry Definitions
-Angle of attack - Lift Equation
-Stall-Stability- Drag on plane and its components...

More good news to come , we are happy to announce that we are officially sponsored by " MathWorks "
28/12/2014

More good news to come , we are happy to announce that we are officially sponsored by " MathWorks "



Address

Tanta University Faulty Of Engineering Saberby Road
Tanta
31521

Telephone

01222601818

Website

Alerts

Be the first to know and let us send you an email when MEC Aero DBF Team posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to MEC Aero DBF Team:

Share