Allied Safety Group

Allied Safety Group Veteran-Owned business dedicated to workplace safety. We help construction & manufacturing achieve OSHA compliance, mitigate risks, and protect lives.

🦺 "One size fits all" doesn't keep anyone safe. A harness that's too loose, gloves that are too big, or eye protection t...
06/19/2026

🦺 "One size fits all" doesn't keep anyone safe. A harness that's too loose, gloves that are too big, or eye protection that won't stay put can leave workers exposed — even when they're wearing the gear.
OSHA's construction PPE standard (29 CFR 1926.95) now says it plainly: employers must ensure PPE properly fits each affected worker. The update brings construction in line with general industry, and it matters most for workers who've long been handed gear that was never sized for them — including smaller workers and women.

A quick gut check for your sites:

✅ Does each worker's PPE actually fit — not just "is it available"?

✅ Can you offer multiple sizes of gloves, harnesses, hi-vis, and eye/face protection?

✅ Does the gear stay in place and do its job during the task?

✅ Do workers feel free to flag gear that doesn't fit — and do you act on it?

✅ Is fit built into your PPE selection and training, not an afterthought?
Properly fitting PPE isn't a new burden — it's gear that actually protects.

Questions about keeping your team safe?

Contact Allied Safety Group: 309.339.8950 | [email protected]

Every worksite is different. Use this information as a starting point and always review your procedures against current OSHA requirements and your company's policies. This is educational content, not legal advice.

👷 This week is OSHA's Trench Safety Stand Down (June 15–19) — a good reminder that a trench can cave in within seconds, ...
06/18/2026

👷 This week is OSHA's Trench Safety Stand Down (June 15–19) — a good reminder that a trench can cave in within seconds, with little warning. If your crews dig, grade, or lay pipe this summer, now's the time for a quick huddle.

OSHA requires protective systems for any trench 5 feet deep or more (unless it's in stable rock). Keep it simple: Slope it. Shore it. Shield it.

Before anyone enters a trench:

✅ Have a competent person inspect it before each shift — and again after rain or any change in conditions

✅ Use sloping, shoring, or a trench box for trenches 5+ feet deep

✅ Keep a safe way out (ladder, ramp, or steps) within 25 feet of workers in trenches 4+ feet deep

✅ Keep spoil piles, equipment, and traffic back from the edge

✅ Never enter a trench that hasn't been protected and inspected
Take 10 minutes this week for a toolbox talk. It's free, it's simple, and it gets everyone home.

Questions about keeping your team safe? Contact Allied Safety Group: 309.339.8950 | [email protected]

Every worksite is different. Use this information as a starting point and always review your procedures against current OSHA requirements and your company's policies. This is educational content, not legal advice.

⚠️ Severe weather is moving across central Illinois today, with the strongest storms expected this afternoon and into th...
06/17/2026

⚠️ Severe weather is moving across central Illinois today, with the strongest storms expected this afternoon and into the evening. Is your crew clear on what to do if a warning hits mid-shift?

A quick refresher can make all the difference:
✅ Know the difference: a watch means conditions are right — stay alert and be ready to act. A warning means take shelter now.

✅ Identify your shelter before you need it — a small interior room or hallway on the lowest level, away from windows and doors. Underground is best.

✅ Account for everyone. Know who's on site and assign someone to do a head count.

✅ Keep a NOAA weather radio, flashlights, and a first aid kit where your team shelters.

✅ On a jobsite? Stop rooftop, scaffold, and crane work early and get people to safe ground.
Stay weather-aware, trust the alerts, and don't wait until the sky tells you it's too late.

Questions about keeping your team safe? Contact Allied Safety Group: 309.339.8950 | [email protected]

Every worksite is different. Use this information as a starting point and always review your procedures against current OSHA requirements and your company's policies. This is educational content, not legal advice.

🦺 Falls are still the leading cause of death in construction — and nearly every one is preventable.CPWR data shows more ...
06/15/2026

🦺 Falls are still the leading cause of death in construction — and nearly every one is preventable.

CPWR data shows more than 1,000 construction workers have died on the job each year since 2016, with more than a third of those deaths caused by falls to a lower level. The fix isn't complicated, but it has to happen before boots hit the deck.

Build fall protection into the job:

🪜Identify fall hazards before work begins — roof edges, openings, ladders, scaffolds
🪜Use guardrails, covers, or personal fall arrest systems where needed
🪜Inspect harnesses, lanyards, and anchor points before each use
🪜Make sure ladders are rated for the job and set at the correct angle
🪜Train every worker who could be exposed to a fall

Planning for falls before they happen is the difference between a near-miss and a tragedy.

Questions about keeping your team safe? Contact Allied Safety Group: 309.339.8950 | [email protected]

⚠️ That cut-off saw kicks up more than dust.A CPWR review of OSHA fatality data tied cut-off saws to serious struck-by i...
06/12/2026

⚠️ That cut-off saw kicks up more than dust.

A CPWR review of OSHA fatality data tied cut-off saws to serious struck-by injuries and fatalities, along with exposure to hazardous silica dust. Respirable crystalline silica can cause irreversible lung disease — and it's invisible while you breathe it in.

Protect your crew:

🦺 Control dust at the source with wet cutting or a vacuum dust-collection system
🦺 Provide the right respiratory protection when dust controls aren't enough
🦺 Inspect the blade and guard before every use, and replace damaged blades
🦺 Keep a firm two-handed grip and clear bystanders from the cutting path
🦺 Train workers on kickback, safe blade selection, and dust controls

Small tool, big hazards — both the kind you see and the kind you don't.

Every worksite is different. This is educational content, not legal advice.

Questions about keeping your team safe?

Contact Allied Safety Group: 309.339.8950 | [email protected]

👷 Here's some encouraging news from the latest construction safety research.CPWR's Safety Management in the Construction...
06/11/2026

👷 Here's some encouraging news from the latest construction safety research.

CPWR's Safety Management in the Construction Industry 2026 report found that smaller contractors are leading recent gains in safety engagement — but gaps remain in preconstruction planning, the use of safety technology, and mental health support.

The takeaway?

Having a safety program isn't the same as having a strong one.

Where employers can level up:

📐 Plan for hazards before the job starts — not after something goes wrong
📊 Track incidents and near-misses so you can spot trends early
🧠 Pay attention to worker mental health and well-being
📐Match training and PPE to the actual tasks on site

Whether you're formalizing a safety program for the first time or tightening one you already have, our team can run a site audit, help with preconstruction hazard planning, and train your crews and supervisors.

Questions about keeping your team safe? Contact A llied Safety Group: 309.339.8950 | [email protected]

⚡ Some of the most serious injuries on a jobsite come from something a worker never saw coming.Struck-by incidents are t...
06/10/2026

⚡ Some of the most serious injuries on a jobsite come from something a worker never saw coming.

Struck-by incidents are the second leading cause of death among construction workers — and the leading cause of nonfatal injuries in the industry. They happen when someone is hit by a moving, flying, falling, or swinging object: vehicles, loads, dropped tools, or equipment.

How to cut the risk:

🚧 Keep workers out of the swing radius and blind spots of heavy equipment
🦺 Use high-visibility gear and spotters around moving vehicles
🔧 Secure tools and materials at height to prevent dropped objects
🚧 Never stand under suspended loads, and inspect rigging before each lift
🦺 Plan the site so people and machines aren't sharing the same space

A few minutes of planning before the work starts prevents the incidents nobody sees coming.

Questions about keeping your team safe? Contact Allied Safety Group: 309.339.8950 | [email protected]

⚠️ The heat is back — and so is OSHA's attention to it.OSHA reissued its National Emphasis Program for outdoor and indoo...
06/10/2026

⚠️ The heat is back — and so is OSHA's attention to it.

OSHA reissued its National Emphasis Program for outdoor and indoor heat-related hazards, effective April 10, 2026, and inspections are being prioritized on days when the heat index climbs above 80°F.

Most heat tragedies are preventable, and the core message stays simple: Water. Rest. Shade. Occupational Safety and Health AdministrationOccupational Safety and Health Administration
Here's what protects your crew:

💧 Provide cool water and encourage workers to drink every 15 minutes Occupational Safety and Health Administration
🌳 Build in frequent rest breaks in the shade as the heat rises
👷 Acclimatize new and returning workers — nearly half of heat-related deaths happen on a worker's first day, and more than 70% in the first week Occupational Safety and Health Administration
📋 Have an emergency plan and train workers to recognize the signs of heat illness Occupational Safety and Health Administration
Don't forget indoor crews — heat hazards happen inside, too

Our team can assess your heat exposure, help you build a written prevention plan, and train your supervisors before inspection season peaks.

Every worksite is different. This is educational content, not legal advice.

Questions about keeping your team safe?
Contact Allied Safety Group: 309.339.8950 | [email protected]

Before your crew heads out, ask yourself: does everyone on your site know what to do when the storm rolls in?Under OSHA’...
06/05/2026

Before your crew heads out, ask yourself: does everyone on your site know what to do when the storm rolls in?

Under OSHA’s General Duty Clause, employers are required to protect workers from recognized hazards, including lightning and severe weather.

For outdoor worksites, that means having a written plan that spells out when to stop work, how workers are notified, where shelter is located, and when it is safe to get back out there.

Who is monitoring weather conditions throughout the day

Where workers go for shelter — identified for every area of the site

Clear triggers for suspending work: thunder heard, lightning visible, or dark or rotating clouds present

Whether all workers — not just supervisors — have been walked through the plan

If your site includes scaffold or crane operations, OSHA has additional requirements during high winds and storms. Make sure your plan addresses those specifically.

The time to make the call is before the weather hits — not during it. Workers count on employers and supervisors to lead on this.
Allied Safety Group helps construction and industrial employers build Emergency Action Plans that are practical, site-specific, and aligned with OSHA requirements. Reach out to our team today — especially with tomorrow’s forecast in mind.

Every worksite is different. Use this information as a starting point and always review your procedures against current OSHA requirements and your company’s policies. This is educational content, not legal advice.

Heat illness is one of those hazards that can sneak up fast—especially when crews are trying to push through a schedule....
06/04/2026

Heat illness is one of those hazards that can sneak up fast—especially when crews are trying to push through a schedule.

Right now, OSHA is moving forward on a Heat Injury and Illness Prevention standard that would apply to both outdoor and indoor work (general industry, construction, maritime, and agriculture where OSHA has jurisdiction).

Even before anything becomes final, the best employers are already tightening up the basics:
⚠️ A written heat plan that’s clear on who does what (supervisors, leads, workers)
Heat “trigger” points (when you step up breaks, water, shade/cooling, and observation)
⚠️Acclimatization for new/returning workers (especially early season)
Training that teaches early warning signs and what action to take fast
⚠️Emergency response steps your supervisors can execute without guessing

If you want, our team can help you pressure-test your heat plan (field-ready, supervisor-friendly, and aligned to current OSHA direction).

Every worksite is different—use this as a starting point and always review your procedures against current OSHA requirements and your company policies. This is educational content, not legal advice.

Address

820 Oakwood Road
East Peoria, IL
61611

Opening Hours

Monday 7am - 5pm
Tuesday 7am - 5pm
Wednesday 7am - 5pm
Thursday 7am - 5pm
Friday 7am - 5pm

Website

Alerts

Be the first to know and let us send you an email when Allied Safety Group posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Allied Safety Group:

Shortcuts

Featured

Share