Description: KARA FALEZ Products:
Standard Doors,
Door Construction,
Door Features,
Specialty Doors,
Standard Frames,
Specialty Frames,
Fire Ratings,
Kara Falez is proud to offer the higest quality steel doors and frames. We stock many common types or we can manufacture most custom doors and frames according to your specific requirements.
2.4.4.1 Wall Anchors
Provide at least three anch
ors for each jamb. For frames which are more
than 2285 mm in height, provide one additional anchor for each jamb for
each additional 760 mm or fraction thereof. Masonry: Provide anchors of corrugated or perforated steel straps
or 5 mm diameter steel wire, adjustable or T-shaped;
c. Completed openings: Secure frames to previously placed concrete
or masonry with expansion bolts in accordance with SDI/DOOR 111;
and
2.4.4.2 Floor Anchors
Provide floor anchors drilled for 10 mm anchor bolts at bottom of each jamb
member. Where floor fill occurs, terminate bottom of frames at the
indicated finished floor levels and support by adjustable extension clips
resting on and anchored to the structural slabs. SECTION 08 11 13 Page 4
Site-Adapt Design ANA Arch-Span Kandaks 122635
Afghanistan
2.5 FIRE AND SMOKE DOORS AND FRAMES
NFPA 80 and NFPA 105 and this specification. The requirements of NFPA 80
and NFPA 105 shall take precedence over details indicated or specified.
2.5.1 Door and Frame Labels
Fire doors and frames shall bear the label of Underwriters Laboratories
(UL), Factory Mutual Engineering and Research (FM), or Warnock Hersey
International (WHI) attesting to the rating required. Labels shall be metal with raised
letters, and shall bear the name or file number of the door and frame
manufacturer. Labels shall be permanently affixed at the factory to frames
and to the hinge edge of the door. Door labels shall not be painted.
2.5.2 Oversized Doors
For fire doors and frames which exceed the size for which testing and
labeling are available, furnish certificates stating that the doors and
frames are identical in design, materials, and construction to a door which
has been tested and meets the requirements for the class indicated.
2.5.3 Astragal on Fire and Smoke Doors
On pairs of labeled fire doors, conform to NFPA 80 and UL requirements. On
smoke control doors, conform to NFPA 105.
2.6 WEATHERSTRIPPING
As specified in Section 08 71 00 DOOR HARDWARE.
2.7 HARDWARE PREPARATION
Provide minimum hardware reinforcing gages as specified in SDI/DOOR A250.6. Drill and tap doors and frames to receive finish hardware. Prepare doors
and frames for hardware in accordance with the applicable requirements of
SDI/DOOR A250.8 and SDI/DOOR A250.6. For additional requirements refer to
BHMA A115. Drill and tap for surface-applied hardware at the project site. Build additional reinforcing for surface-applied hardware into the door at
the factory. Locate hardware in accordance with the requirements of
SDI/DOOR A250.8, as applicable. Punch door frames to receive a minimum of
two rubber or vinyl door silencers on lock side of single doors and one
silencer for each leaf at heads of double doors. Set lock strikes out to
provide clearance for silencers.
2.8 FINISHES
2.8.1 Electrolytic Zinc-Coated Anchors and Accessories
Provide electrolytically deposited zinc-coated steel in accordance with
ASTM A 879/A 879M, Commercial Quality, Coating Class A. Phosphate treat
and factory prime zinc-coated surfaces as specified in SDI/DOOR A250.8.
2.8.2 Factory-Applied Enamel Finish
Coatings shall meet test procedures and acceptance criteria in accordance
with SDI/DOOR A250.3. After factory priming, apply two coats of
medium-gloss enamel to exposed surfaces. Separately bake or oven dry each
coat. Drying time and temperature requirements shall be in accordance with
Our commitment to rebuilding our country
Their precious time into the study Nmdyd
KARA FALEZ Factory
Between The four Traffic Kolola Pushta, Taimani Kabul
Afghanistan
Contacts: +93(0)788016688
Email:[email protected]
