SND3D

SND3D Professionally 3D printed high quality functional and articulated models.

Simple little fix to my monkeys tail cactus. I'm a beautiful mind when I 3d print 😁 🙌🏼🫶🏻 I am looking for a monkey to pr...
28/11/2023

Simple little fix to my monkeys tail cactus. I'm a beautiful mind when I 3d print 😁 🙌🏼🫶🏻 I am looking for a monkey to print to replant it in. Feel free to comment and links or share your thoughts.

In the spirit of the holidays, plus the fact i have a few too many printers 🤣I would like to hold a little competition 🙌...
28/11/2023

In the spirit of the holidays, plus the fact i have a few too many printers 🤣

I would like to hold a little competition 🙌🏼 , which will be ending on the 25th December 2023.

I have an Adventure 3 with a printed enclosure for holding a 1kg roll to give away 🫶🏻 plus a roll of eSun PLA 😁 postage will be covered by myself and if you're a Brisbane local I'm sure we could organise a collection point if you'd prefer.

Terms - Comment what would be your first print on this small but powerful machine 😏 even post the link too 🤙🏼

The winner will be the comment with the most likes. So share and spread the word.

This is my first giveaway, so it is only open to Australian residents. My apologies to all my international followers 🙌🏼 I'll see what I can do for the next one

Pictured is a printed doorstop using TPU. It has printed carbon fibre, TPU, ABS, and PLA without any issues.

Finally got a decent print from the Creator 3 Pro. I've tried a wiping tower, no wiping tower and now wall. I'm happy wi...
26/11/2023

Finally got a decent print from the Creator 3 Pro. I've tried a wiping tower, no wiping tower and now wall. I'm happy with the results 🙌🏼

The first print is done for the T-800 project. Big rookie mistake was made 🤦‍♂️I didn't double check the orientation for...
26/11/2023

The first print is done for the T-800 project. Big rookie mistake was made 🤦‍♂️I didn't double check the orientation for the foot with the and it was labelled left foot. When, in fact, it's the right foot, and I should've flipped it 180 degrees. Good thing the support came off easily enough and no real reason to reprint unless I want perfect 🙌🏼🫶🏻

-800 #🤦‍♂️

Well I got this printer (well 2 cause I have a problem) 🤣 First print off the microsd card to the printer is a 24hr prin...
24/11/2023

Well I got this printer (well 2 cause I have a problem) 🤣 First print off the microsd card to the printer is a 24hr print 😳 left foot for full scale T-800 model from thingiverse 🙌🏼 I'll set the second one up tomorrow.

Also got 6 rolls of PLA Grey specifically from sunlu for the colour 🫶🏻

foot

Long story short, came across this printer at a price I couldn't resist. Now the fun begins. First time seeing this bran...
23/11/2023

Long story short, came across this printer at a price I couldn't resist. Now the fun begins. First time seeing this brand. So far the packaging was flawless and even the check-list all ticked made me happy 🫶🏻 I'll do up another post later once built and working

Huge 29 hour spiral print using a 0.8mm nozzle. This planter is nearly as big as the Adventurer 3 🤣 I'll definitely be d...
17/11/2023

Huge 29 hour spiral print using a 0.8mm nozzle. This planter is nearly as big as the Adventurer 3 🤣 I'll definitely be doing more of these. Maybe a little bit smaller than this one 🤔

First completed print using Flashforge Creator Pro 3. Love how you can print 2 models at the same time with the IDEX. Th...
17/11/2023

First completed print using Flashforge Creator Pro 3. Love how you can print 2 models at the same time with the IDEX. There's normal, mirror, and duplicate modes. This is an example of mirror mode, and watching the 2 extruder working is amazing 😍🫶🏻

One good thing with this printer is I can print 2 models for the same time to print one 🤙🏼

Big thanks to North Lakes for looking after me with the purchase of this beautiful 😍 machine

Making these little beauties up to promote work. The QR code is a direct link to the model written on the base. Finger...
16/11/2023

Making these little beauties up to promote work. The QR code is a direct link to the model written on the base. Finger crossed, we can get people to support him with the hope of new designs being made in the future 🫶🏻🙌🏼

This po station will be used to print all of models over the next few months. Saved a spot for a second Adventurer 5M ...
15/11/2023

This po station will be used to print all of models over the next few months. Saved a spot for a second Adventurer 5M Pro. These 3 models have been trouble-free and performed remarkably. Being able to connect them all with an 8 port switch and to control them from your PC saves using USB. They also have other networking connections too.

A modification from thingiverse for the Adventurer 3 to house a 1kg roll was ptinted. This designer made it fit on the Adventurer 3 so you could use the PLA that comes with the machine. Also, don't let the small build fool you, it handle the Carbon Fibre PLA with ease 😉

Flashforge has always built their printers to last, too.

North Lakes gave me a deal I couldn't refuse. As always, they look after me with my local 3d printing supplies 🫶🏻

I was introduced to designs and fell in love with them all, so much I ended up purchasing all his premium models. Thos...
15/11/2023

I was introduced to designs and fell in love with them all, so much I ended up purchasing all his premium models. Those who know me in real life have seen the models I have done. Some at 200% scale as well.

https://www.toymakr3d.com/product/71-kingtiger

Since I'll be spending the holidays this year alone again with my 3d printers, I'll be printing all the premium models again at 100% scale.

Here's Kingtiger and I have used marble PLA and Carbon Fibre PLA from North Lakes to enhance the print.

So after realising i needed to slow the laser down to 6.6 mm/s @ full power to cut through this 5mm piece, this was the ...
08/11/2023

So after realising i needed to slow the laser down to 6.6 mm/s @ full power to cut through this 5mm piece, this was the end result.

Only using the supplied metal piece they give you as my board. Waiting for the 400 x 400mm honeycomb board to arrive soon 🙌🏼

Address

Brisbane, QLD

Website

Alerts

Be the first to know and let us send you an email when SND3D posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to SND3D:

Shortcuts

Featured

Share

Category