Foshan Leabon Machinery Co., Ltd.

02/10/2026

A square block goes in. A complex curved gun model form comes out. 🔥
Turn-mill compound 5-axis machining — one setup, zero re-clamping.

02/10/2026

For most shops, drilling a panel means flipping it, re-fixturing it, and running it through again — for the back, for the edges, for the groove. Every flip is time, labor, and a chance for misalignment.

Leabon SG-612S removes the flipping. In a single setup it drills the front face, the back face, and the side edges — then cuts the surface groove, all in one cycle. No turning the panel over. No second machine for the groove.

What that means on your floor:
✅ All six faces drilled in one clamping — front, back, and four edges
✅ Surface grooving handled in the same pass — drilling + grooving in one machine
✅ No panel flipping, no re-fixturing — fewer alignment errors, faster cycles
✅ Built for custom and high-mix panel work where every job is different

02/10/2026

Choosing the right laminate press can directly impact panel quality, production speed, and long-term operating costs. Our guide covers key press types, performance factors, automation options, and selection criteria for furniture factories working with MDF, particleboard, plywood, and decorative laminates. It’s a practical resource for production managers and purchasing teams comparing equipment for reliable, scalable panel processing.

https://www.lbmachinery.com/en/2026/10/02/laminate-press-guide-furniture-factories/

02/10/2026

Laminate Press Guide for Furniture Factories

This laminate press guide helps furniture factories select hot, cold, and vacuum presses for reliable bonding, higher output, and less daily rework at scale....

This laminate press guide helps furniture factories select hot, cold, and vacuum presses for reliable bonding, higher output, and less daily rework at scale.

01/10/2026

Drop the board at the infeed and walk away. Our auto-feed band saw reads the thickness with an infrared sensor, clamps your material, and feeds it through — no reach-ins, no close calls, just the same clean cut every time. Safer by design.

30/09/2026

Most handle-less lines force you to commit to one pull profile — one machine, one shape, and a costly changeover if the trend shifts.

The Leabon LZJ-968 mini soft-forming edge ba**er takes a different route:

✅ Interchangeable molds — swap the forming tool and the same mini machine produces J-pull, Gola, water-drop and other handle-less profiles
✅ Soft-forming by heating lamp — the edge band is softened and pressed onto the handle-less section in one cycle
✅ Mini footprint — an R&D new model built compact, so small shops can run handle-less lines too
✅ ~30 seconds per piece — load the mold, align the panel, clamp, band, heat, press; consistent result, low labor
✅ One machine, many profiles — flexibility that keeps you ahead of changing cabinet-front trends

For custom kitchen, wardrobe and cabinet makers who want handle-less variety without a floor full of single-shape iron.

Want the machine price? Comment or DM us.

30/09/2026

Raw blank ➜ finished mold, all on one machine. This is what 5-axis freedom looks like: curves no hand plane can match, surface ready for the mold shop. Save this one ✨
DM me for the machine price.

29/09/2026

If your team is still squaring cabinet frames by hand — clamp by clamp, corner by corner — you already know the problems: it's slow, it's inconsistent, and "close enough" shows up later as crooked doors and messy glue lines.

The Leabon MH2525 cabinet frame press takes that whole routine off your floor. Load a glued frame, close the press, and the platens square every corner at once — tight joints, clean glue lines, every single time. No hand squaring. No clamps to tighten. No "good enough" frames.

Built on a full channel-steel frame (not thin sheet metal) and manufactured in our own factory, the MH2525 is also customizable — size, pressure, and configuration matched to your door and frame dimensions.

👉 DM me and we'll send the MH2525 spec sheet, working envelope, and lead time.

29/09/2026

Stack the logs, press start. The line does the rest — feeding, cutting to length, and stacking, all on its own. Save this for your next shop upgrade ✨

28/09/2026

40mm strip. Long edge. Fully banded — both ends rounded.
Pre-mill → glue → end cut → trim → corner-round → scrape → buff.
Even the narrow strip comes off clean.
DM me for the machine price.
**er