MPC Gun Works LLC

Call Directions Contact the business

MPC Gun Works LLC GUNSMITH
Type 7 FFL Manufacturer
Custom Builds
Repairs
Modifications
Restorations-Conservation

C**t Trooper Mark III 6” Blued chambered for .357 mag DOM; 1976Customer states; very few rounds through it. Unknown when...
07/08/2026

C**t Trooper Mark III 6” Blued chambered for .357 mag DOM; 1976
Customer states; very few rounds through it. Unknown when last serviced.
Cylinder won’t open.
Pistol was stiff. Stuck cylinder stop and hammer wouldn’t cycle DA.
Disassembled and found dried grease build up and light interior rust. The double action lever & cylinder latch bolt were seized with dried grease. After a detailed clean to remove the build up all parts cycled through the sonic cleaner.
After proper lubrication, a function check then a test fire has it ready for duty. The muzzle wear was cleaned and given a cold blue application and blended in.

11/12/2025

One more pass and this damaged stock will be ready for replacement wood.

11/12/2025

Today brings a bit of stock repair to do.
One more pass should clean it up.

Wi******er XPR 6.5 came in for muzzle threading for a suppressor. The barrel muzzle did not have enough material to thre...
09/08/2025

Wi******er XPR 6.5 came in for muzzle threading for a suppressor. The barrel muzzle did not have enough material to thread the 5/8-24 required to install the suppressor, so we turned and threaded the muzzle to 0.750”X 1/2-24 to accept the Banish adapter; 1/2-24 to 5/8-24.
The rifle was ready for pickup once the Bore to Baffle alignment was checked and approved.
Ready for the range.

Customer requested the muzzle be threaded to accept a Banish 30 direct thread suppressor & a deep clean on an Olympic Ar...
12/14/2024

Customer requested the muzzle be threaded to accept a Banish 30 direct thread suppressor & a deep clean on an Olympic Arms rifle chambered in .22-250
The barrel was indicated in the lathe aligned with the bore. The video in comments shows the barrel set and ready for single point threading. After threading, the suppressor was temporarily installed to work out the timing. Then an alignment check for baffle clearance; pass. After a sonic clean the rifle was reassembled and function checked.
Customer will reinstall the scope.

R***r MK II chambered in .22 LR came in for a deep clean. Started with a function check; pass, test fire had occasional ...
08/06/2024

R***r MK II chambered in .22 LR came in for a deep clean. Started with a function check; pass, test fire had occasional misfires and cycling issues.
Disassembled the pistol & magazine.
Inspect all parts, all are serviceable.
Sonic clean all parts.
Reassembled pistol & magazine.
Function check; pass
Test fire; pass
MPC Gun Works LLC
Farmland, In.

Browning 25 auto, chambered in…(drum roll)… .25 acp. Customer stated it would not cycle. Failed function check, so no te...
08/06/2024

Browning 25 auto, chambered in…(drum roll)… .25 acp. Customer stated it would not cycle. Failed function check, so no test fire. During disassembly & inspection of parts, all internals were oily with lots of carbon buildup and lint. The trigger bar was not set in its proper location at the rear of the frame. All parts appear functional. After a sonic clean a light, very light film of gun oil & then reassembly.
Function check; pass
Test fire; pass
Customer stated they removed the scales. These small mouse guns rely on the scales to hold the trigger bar in place.
MPC Gun Works LLC
Farmland, In
(765)748-7998

Customer brought in the buttstock for me to see. My, my, she’s a beaut!
06/19/2024

Customer brought in the buttstock for me to see. My, my, she’s a beaut!

Uberti Buntline in .45colt. Customer wanted to change the 10 5/8” barrel to an 18” barrel. Disassembled & receiver wrenc...
06/18/2024

Uberti Buntline in .45colt.
Customer wanted to change the 10 5/8” barrel to an 18” barrel.
Disassembled & receiver wrench installed on the frame. Mounted the barrel in the barrel vise for barrel removal.
Inspect & clean interior threads along with the threads on the new barrel tenon.
Install barrel.
Reassemble
Check & adjust the headspace.
MPC Gun Works LLC
Farmland, In
(765)748-7998

Stoeger M3000 chambered for 12 ga. Customer requested a stock recoil reducer be installed. No vendor had this part in st...
01/25/2024

Stoeger M3000 chambered for 12 ga.
Customer requested a stock recoil reducer be installed. No vendor had this part in stock so a shop fabrication was in order. Using a section of barrel blank, it was turned to 0.875” x 4.50”. After drilling, it was tapped for M8-1.0 then to the mill for an installation slot.
Reassembled and test fired.
Quite a difference.

MPC Gun Works LLC
Farmland, In
Facebook: mpcgunworks
[email protected]

Address

8628 West State Road 1
Farmland, IN
47340

Telephone

+17657487998

Website

Alerts

Be the first to know and let us send you an email when MPC Gun Works LLC posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to MPC Gun Works LLC:

Shortcuts

Share

Category