JFC Engineering Services

JFC Engineering Services Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from JFC Engineering Services, Business service, Gate Farm, Elmsett, Ipswich.

At JFC Engineering, service means excellence in the delivery of each and every of our services associated with installation, repair, maintenance, overhaul, modification and projects across a wide variety of domestic, commercial and industrial environments

07/04/2022
I was asked by my son today if I could weld up his mates exhaust... it was a bit worse than he expected..so I fitted Cha...
14/04/2021

I was asked by my son today if I could weld up his mates exhaust... it was a bit worse than he expected..so I fitted Charlie’s spare pipe to keep him going until he can get a new one.

20/01/2021

KTM crank bearing removal tool in action. The inner race of the bearing is a shrink fit to the shaft and is tight up against the crank web so removing it is very difficult. This is why the only tool is the right tool for the job.

Very important breakdown tonight.. The Dyson washing machine was making a horrendous noise. On investigation found the p...
30/12/2020

Very important breakdown tonight.. The Dyson washing machine was making a horrendous noise. On investigation found the planetary gear drive for the contra rotation drive had s**t its self... so off to the workshop to keep this machine going....

Another nest install today. This was a 2 zone heating system so required 2 Nest’s to be installed. All setup and custome...
26/11/2020

Another nest install today. This was a 2 zone heating system so required 2 Nest’s to be installed. All setup and customer was shown how to get the most from it using the app.

Tricky job skimming some very large brake discs, started on the Colchester lathe but ended up doing the job on the mill,...
17/11/2020

Tricky job skimming some very large brake discs, started on the Colchester lathe but ended up doing the job on the mill, this way I could ensure both sides were machined parallel...

I have been asked by a local company to build them a control panel for a custom spray booth. I am just finishing the pro...
22/10/2020

I have been asked by a local company to build them a control panel for a custom spray booth. I am just finishing the programming and testing. This allows a dual temperature to be set in the room, one for spraying and one for baking. The baking time can be set from the control panel.

I was asked to make a fork clamp, this is to enable a motocross or enduro fork leg to be clamped using a workshop vice w...
19/10/2020

I was asked to make a fork clamp, this is to enable a motocross or enduro fork leg to be clamped using a workshop vice without damaging the tube, so the bottom can be unscrewed.

I now have the facility to chemically strip paint from motorcycle crank cases, this helps give a better result when vapo...
29/07/2020

I now have the facility to chemically strip paint from motorcycle crank cases, this helps give a better result when vapour blasting.

And this is why you need to PAT test your appliances.. found today.
26/05/2020

And this is why you need to PAT test your appliances.. found today.

I have been working with a customer to make a lab machine suitable for production level output. Having agreed on a spec ...
17/05/2020

I have been working with a customer to make a lab machine suitable for production level output. Having agreed on a spec I have produced a machine for them to use. It is a tilting table machine and is used to strip circuit boards with bacteria that need to be kept at a optimum temperature and in a moving solution.

Here is some progress on a job I am currently on, it’s a screen for a large industrial shredder.
25/02/2020

Here is some progress on a job I am currently on, it’s a screen for a large industrial shredder.

Address

Gate Farm, Elmsett
Ipswich
IP76

Opening Hours

Monday 7:30am - 5pm
Tuesday 7:30am - 5pm
Wednesday 7:30am - 5pm
Thursday 7:30am - 5pm
Friday 7:30am - 5pm
Saturday 7:30am - 1pm

Telephone

+447961921808

Alerts

Be the first to know and let us send you an email when JFC Engineering Services posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to JFC Engineering Services:

Share