08/10/2026
මහජන උපයෝගිතා කොමිසන් සභාව මගින් ප්රකාශයට පත් කරන ලද , Roof top solar සහ Battery පද්ධති(BESS) සදහා වන නවතම රෙගුලාසී...🔋☀️
සාරාංශය...
ශ්රී ලංකාවේ RTSPV + BESS Installation කරන ඔබ දැනගත යුතු වැදගත් Technical & Safety Requirements
Solar PV system එකකට Battery Energy Storage System (BESS) එකක් එකතු කිරීම කියන්නේ battery එකක් සහ inverter එකක් install කරන එක විතරක් නෙමෙයි.
System sizing, battery performance, protection, fire safety, grid compliance, monitoring සහ commissioning යන සියලුම කරුණු නිවැරදිව design කරලා implement කළ යුතුයි.
📌 BESS Installer / Solar Professional කෙනෙක් අනිවාර්යයෙන් අවධානය යොමු කළ යුතු කරුණු 👇
🔹 1. SLSEA Registration & Compliance
Solar PV/BESS installation කරන service provider/installer කෙනෙක්ට අදාළ registration සහ regulatory requirements නිවැරදිව follow කළ යුතුයි.
🔹 2. Chartered Electrical Engineer Involvement
System design, compliance සහ declaration requirements සඳහා අවශ්ය අවස්ථාවල Chartered Electrical Engineer කෙනෙකුගේ certification/declaration අවශ්ය වේ.
🔹 3. Battery Capacity – Inverter Capacity Ratio
BESS sizing කරන විට වැදගත් requirement එකක්:
👉 Usable Battery Capacity ≤ Inverter Capacity × 5 hours
උදාහරණයක් ලෙස,
10 kW inverter එකක් නම් → 50 kWh usable battery capacity දක්වා යන sizing එක මේ requirement එකට අනුව consider කළ හැක.
මෙම සීමාව ඉක්මවා යන්නේ නම්, detailed technical assessment එකක් සහ Chartered Electrical Engineer කෙනෙකුගේ written recommendation එකක් අවශ්ය විය හැක.
🔹 4. Lithium-Based Battery Technology
මෙම technical specification එක යටතේ lithium-based battery systems සඳහා අවශ්ය technical requirements සලකා බැලිය යුතුයි.
🔹 5. Battery Voltage
BESS system එකේ nominal DC voltage එක 1500 V ට වැඩි නොවිය යුතුය යන technical scope එක සැලකිල්ලට ගත යුතුයි.
🔹 6. Battery Efficiency – අවම 85% ⚡
Battery system එකේ round-trip efficiency එක:
✅ Standard – ≥ 85%
⭐ Premium – ≥ 90%
ඒ නිසා battery quotation එකේ capacity එක විතරක් බලන්නේ නැතුව usable energy සහ efficiency දෙකම බලන්න.
🔹 7. Battery Cycle Life 🔋
🏠 Residential BESS: අවම 6,000 cycles
🏢 Commercial / Industrial BESS: අවම 8,000 cycles
එම cycle-life requirements සමඟ battery performance එක 80% Depth of Discharge (DoD) සහ 80% End-of-Life capacity වැනි conditions යටතේ consider කළ යුතුයි.
🔹 8. 80% DoD කියන්නේ මොකක්ද?
Battery එකේ සම්පූර්ණ capacity එකම සෑම දිනකම භාවිතා කරනවා වෙනුවට, specified DoD එකක් තුළ operate කිරීම battery life සහ performance සඳහා වැදගත්.
ඒ නිසා:
Battery Nominal Capacity ≠ Always Available Usable Energy
Battery sizing කරන විට මෙය අනිවාර්යයෙන් consider කරන්න.
🔹 9. BMS – Battery Management System
හොඳ BESS එකකට BMS එකක් අනිවාර්යයි.
BMS එක මගින්:
✅ Cell voltage monitoring
✅ Temperature monitoring
✅ Over-charge protection
✅ Over-discharge protection
✅ Over-current protection
✅ Battery balancing
✅ Fault detection
✅ SOC monitoring
✅ SOH monitoring
වැනි functions කළ යුතුයි.
🔹 10. Inverter / PCS Requirements
BESS inverter/Power Conversion Equipment (PCE) එක:
✅ Pure Sine Wave output
✅ Grid synchronization
✅ Required protection functions
✅ Battery charging/discharging control
✅ Grid-support functions
වැනි requirements සපුරාලිය යුතුයි.
🔹 11. Grid Support Functions ⚡🌐
අදාළ system/inverter එකට අවශ්ය අවස්ථාවල:
• LVRT – Low Voltage Ride Through
• AFCI – Arc Fault Circuit Interruption
• Volt-VAR control
• Volt-Watt control
වැනි grid-support සහ protection functions තිබිය යුතුයි.
🔹 12. >50 kW Systems සඳහා Communication
Inverter capacity එක 50 kW ට වැඩි නම් utility/distribution network එක සමඟ monitoring සහ control communication requirements සැලකිල්ලට ගත යුතුයි.
🔹 13. Remote Monitoring & Cybersecurity
BESS system එකේ performance සහ operating data monitor කිරීමට remote monitoring facility එක තිබීම වැදගත්.
ඒ වගේම remote communication links සඳහා encryption සහ cybersecurity measures අවශ්ය වේ.
🔹 14. IP54 Protection
BESS equipment සඳහා අවශ්ය environmental protection එක නිවැරදිව select කළ යුතු අතර specification අනුව IP54 protection requirement එක සැලකිල්ලට ගත යුතුයි.
🔹 15. BESS Installation Location 🏠
Battery system එක install කරන ස්ථානයේ:
✅ Adequate ventilation
✅ Heat management
✅ Safe access
✅ Emergency access
✅ Fire safety
✅ Environmental protection
වැනි කරුණු design stage එකේදීම consider කරන්න.
🔹 16. Fire Safety 🔥
BESS installation එකේ fire risk එක ඉතා වැදගත්.
ඒ නිසා:
🔥 Fire detection
🔥 Appropriate fire suppression arrangements
🔥 Emergency Shutdown (ESD)
🔥 Thermal runaway mitigation
🔥 Safe separation / installation arrangements
වැනි කරුණු අනිවාර්යයෙන් design එකට ඇතුළත් කළ යුතුයි.
🔹 17. Thermal Runaway Protection
Battery specification එකේ thermal runaway mitigation පිළිබඳ manufacturer information තිබිය යුතු අතර, අදාළ test evidence/standard compliance, උදාහරණයක් ලෙස UL 9540A හෝ equivalent documentation සලකා බැලිය යුතුයි.
🔹 18. DC Cable Protection 🔌
Battery DC cables:
✅ Correct cable sizing
✅ Proper insulation
✅ Mechanical protection
✅ Correct routing
✅ Appropriate termination
✅ Suitable conduit/trunking
සමඟ install කළ යුතුයි.
Exposed BESS cabling සඳහා specified mechanical protection භාවිතා කිරීම වැදගත්.
🔹 19. Cable Standard & LSZH
DC cabling සඳහා applicable standards සහ LSZH (Low Smoke Zero Halogen) cable requirements සැලකිල්ලට ගත යුතුයි.
🔹 20. Surge Protection – SPD ⚡
System එකේ DC සහ AC sides දෙකේම appropriate Surge Protective Devices (SPD) තිබිය යුතුයි.
Minimum Type 2 SPD requirements සහ අදාළ IEC standards consider කළ යුතුයි.
🔹 21. RCD Protection
Residual current protection භාවිතා කරන system වලදී:
👉 Grid connection/PCE-to-PCC සඳහා Type B RCD requirements
👉 EPS side සඳහා manufacturer requirement සහ applicable wiring standards අනුව Type A / Type B
නිවැරදිව select කළ යුතුයි.
🔹 22. Earthing & Protection
BESS system එකේ:
✅ Protective earthing
✅ Equipotential bonding
✅ Fault protection
✅ Isolation
✅ Over-current protection
✅ Short-circuit protection
නිවැරදිව design කර තිබිය යුතුයි.
🔹 23. Single Line Diagram (SLD) 📐
Installation එකට පෙර proper Single Line Diagram එකක් තිබිය යුතුයි.
SLD එකේ:
Solar PV → Inverter → BESS → Main DB/PCC → Grid
සහ protection/isolation devices පැහැදිලිව පෙන්විය යුතුයි.
🔹 24. Protection Coordination Study
Protection devices එකිනෙකට coordinate වෙනවාද කියලා verify කිරීම වැදගත්.
Fault එකක් ඇති වූ විට අදාළ protection device එක නිවැරදිව operate වීම system safety එකට අත්යවශ්යයි.
🔹 25. Battery Performance Documentation
Manufacturer documentation එකේ අවම වශයෙන්:
📄 Rated Capacity
📄 Usable Capacity
📄 Voltage Range
📄 Maximum Charge Current/Power
📄 Maximum Discharge Current/Power
📄 Operating Temperature
📄 Cycle Life
📄 Efficiency
📄 Thermal Safety
📄 Fire Performance
වැනි information තිබිය යුතුයි.
🔹 26. Battery Communication
BMS සහ inverter/EMS අතර communication සඳහා system එකට ගැලපෙන protocols භාවිතා කළ හැක.
උදාහරණ:
CAN Bus / Modbus / RS485 / IEC 61850
වැනි communication methods.
🔹 27. Commissioning – Installation අවසන් වුණා කියන්නේ වැඩේ අවසන් නෙමෙයි!
Commissioning වලදී:
✅ Battery testing
✅ Inverter testing
✅ Protection testing
✅ Communication testing
✅ Emergency shutdown testing
✅ Grid synchronization testing
✅ Monitoring verification
✅ Functional testing
සිදු කළ යුතුයි.
🔹 28. Documentation & Handover
Customerට system එක handover කරන විට:
📁 As-built drawings
📁 SLD
📁 Equipment datasheets
📁 Certificates
📁 Test reports
📁 Commissioning records
📁 Protection settings
📁 Warranty documents
📁 Operation & Maintenance information
ලබාදීම වැදගත්.
🔹 29. Monitoring Data
BESS system එකේ operational data නිවැරදිව record කිරීම අවශ්ය වන අතර, specification අනුව අවම වශයෙන් මාස 12ක monitoring data retention requirement එකක් සලකා බැලිය යුතුයි.
🔹 30. Regular Maintenance
Installation එකෙන් පස්සේත්:
🔧 Battery health
🔧 BMS
🔧 Inverter
🔧 Cooling / ventilation
🔧 Fire detection
🔧 Fire suppression
🔧 ESD
🔧 Protection devices
🔧 Firmware / software
නිතිපතා inspect සහ maintain කළ යුතුයි.
🔹 31. Annual Safety & Performance Checks
අවශ්ය periodic maintenance සමඟ:
✔️ State of Health (SoH)
✔️ Protection tests
✔️ Fire safety system
✔️ ESD system
✔️ BMS operation
✔️ Software/firmware updates
වැනි කරුණු පරීක්ෂා කළ යුතුයි.
🔹 32. End-of-Life / Recycling ♻️
Battery එකේ useful life අවසන් වූ විට disposal එක සාමාන්ය garbage එකක් වගේ සිදු නොකර, proper end-of-life management සහ recycling procedure එකක් තිබිය යුතුයි.
---
Copy